Step by Step How to Programming Instructions:
Programming with Two Recognized Keys
To program a new key:
1. Insert the original, already programmed key in the ignition and turn on the ignition.
2. Turn the ignition off, and remove the key.
3. Quickly, within five seconds, insert the second original already programmed key in the ignition and turn on the ignition.
4. Turn the ignition off, and remove the key.
5. Insert the new key to be programmed and turn the ignition on
within five seconds. The security light will turn off once the key has
been programmed.
6. Repeat Steps 1–5 if additional keys are to be programmed.
Programming without Two Recognized Keys
Program a new key to the vehicle when two recognized keys are not
available. Canadian regulations require that owners see their dealer. If
two currently recognized keys are not available, follow this procedure
to program the first key. This procedure will take approximately 30
minutes to complete for the first key. The vehicle must be off and all
of the keys you wish to program must be with you.
1. Insert the new vehicle key into the ignition.
2. Turn the ignition on. The security light will come on.
3. Wait 10 minutes until the security light turns off.
4. Turn the ignition off.
5. Repeat Steps 2–4 two more times. After the third time, turn the
ignition on; the key is learned and all previously known keys will no
longer work with the vehicle.
6. To program the second key, turn the ignition off and insert the
second key to be learned and turn the ignition on. After the two keys
are learned, remaining keys can be learned by following the procedure in
“Programming with Two Recognized Keys.”
Programming with Recognized Transmitters (Keyless Access Vehicles Only)
A new transmitter can be programmed to the vehicle when there are
two recognized transmitters. To program, the vehicle must be off and all
of the transmitters, both currently recognized and new, must be with
you.
1. Place the two recognized keys in the transmitter pocket. The transmitter pocket is inside the center console storage area.
2. Remove the key lock cylinder cap on the driver door handle. Insert
the vehicle key of the new transmitter into the key lock cylinder on the
outside of the driver door and turn the key to the unlock position five
times within 10 seconds. The Driver Information Center (DIC) displays
READY FOR REMOTE #2, 3, 4 or 5.
3. Place the new transmitter into the transmitter pocket with the
buttons facing toward the rear of the vehicle. The transmitter pocket is
inside the center console storage area.
4. Press ENGINE START/STOP. When the transmitter is learned, the DIC will show that it is ready to program the next transmitter.
5. Remove the transmitter from the front cup holder and press UNLOCK on
the transmitter. To program additional transmitters, repeat Steps 3–5.
When all additional transmitters are programmed, press and hold ENGINE
START/STOP for 12 seconds to exit programming mode.
6. Return the vehicle key back into the transmitter.
Programming without Recognized Transmitters (Keyless Access Vehicles Only)
If two currently recognized transmitters are not available, follow this
procedure to program up to eight transmitters. This feature is not
available in Canada. This procedure will take approximately 30 minutes
to complete. The vehicle must be off and all of the transmitters you
wish to program must be with you.
1. Remove the key lock cylinder cap on the driver door handle. Insert
the vehicle key of the transmitter into the key lock cylinder on the
outside of the driver door and turn the key to the unlock position five
times within 10 seconds. The Driver Information Center (DIC) displays
REMOTE LEARN PENDING, PLEASE WAIT.
2. Wait for 10 minutes until the DIC displays PRESS ENGINE START BUTTON
TO LEARN and then press ENGINE START/STOP. The DIC displays will again
show REMOTE LEARN PENDING, PLEASE WAIT.
3. Repeat Step 2 two additional times. After the third time all
previously known transmitters will no longer work with the vehicle.
Remaining transmitters can be relearned during the next steps. The DIC
display should now show READY FOR REMOTE # 1.
4. Place the new transmitter into the transmitter pocket which is inside the center console storage area.
5. Press ENGINE START/STOP. When the transmitter is learned the DIC will show that it is ready to program the next transmitter.
6. Remove the transmitter from the front cup holder and press UNLOCK on the transmitter.
To program additional transmitters, repeat Steps 4–6. When all
additional transmitters are programmed, press and hold ENGINE START/STOP
for 12 seconds to exit programming mode.
7. Return the vehicle key back into the transmitter.
Order Now: Click to chat