Please make sure to read through the programming instructions completely before attempting.

All remotes that are expected to work for the vehicle will need to be with you in the vehicle before attempting the programming. Any remotes not present at the time of programming will cease to function until reprogrammed.

1. Enter the vehicle, close and unlock all doors using the power lock switch on the driver’s door.

2. Open the driver’s door, then using the key within five (5) seconds, insert and remove the key from the ignition once. The rest of the programming from this point on must be completely within forty-five (45) seconds.

3. Using the power lock switch on the driver’s door, toggle the switch by pressing LOCK and UNLOCK five (5) times in one (1) second cycles, counting each LOCK and UNLOCK cycle as one (1).

4. Close the driver’s door and then open the driver’s door.

5. Repeat STEP 3 once, then proceed to STEP 6.

6. Insert the key into the ignition switch. Switch the key to the ON position as far as it will go without starting and back to the OFF position two (2) times and then remove the key.

At this point the vehicle door locks should automatically lock and unlock twice, indicating that the programming mode has been activated. (If door locks do not cycle automatically than the programming procedure has failed and you need to restart the procedure from STEP 1.

7. On the first remote you wish to program (we recommend programming original remotes first if you have one), press and hold the LOCK and UNLOCK buttons at the same time for 1.5 seconds, release, then press and hold LOCK for one (1) second and release. The door locks will automatically cycle one (1) time to indicate the remote has been programmed successfully. *NOTE* If the door locks cycle twice, this means the registration failed. You can repeat STEP 7 until the locks only cycle one (1) time. If the locks do not cycle one (1) time by themselves, or they stop cycling altogether, then you must repeat the entire programming procedure.

8. If you have additional remotes to program, repeat STEP 7 for all remaining remotes you wish to program (You can program up to 4 remotes total).

9. Once you have programmed all your remotes, exit the programming mode by closing the driver’s door, inserting the key into the ignition, start the vehicle, turn it off, and then remove the key.

10. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.

REMOTE PROGRAMMING (For 2002-2004 Avalon models)

Please make sure to read through the programming instructions completely before attempting.

All remotes that are expected to work for the vehicle will need to be with you in the vehicle before attempting the programming. Any remotes not present at the time of programming will cease to function until reprogrammed.

1. Enter the vehicle, close and unlock all the doors using the power lock switch on the driver’s door.

2. Open the driver’s door and then using the key within five (5) seconds, insert and remove the key from the ignition two (2) times. The rest of the programming from this point on must be completed within forty-five (45) seconds.

3. Close and open the driver’s door two (2) times.

4. Insert and remove the key from the ignition one (1) time.

5. Close and open the driver’s door two (2) times.

6. Insert the key into the ignition switch. Without starting the vehicle, switch the key to the ON position and back to the OFF position two (2) times and then remove the key.

At this point the vehicle door locks should automatically lock and unlock twice, indicating that the programming mode has been activated. (If door locks do not cycle automatically then the programming procedure has failed and you need to restart the procedure from STEP 1)

7. On the first remote you wish to program (we recommend programming original remotes first if you have one), press and hold the LOCK and UNLOCK buttons at the same time for 1.5 seconds, release, then press and hold LOCK for one (1) second and release. The door locks will automatically cycle one (1) time to indicate the remote has been programmed successfully. *NOTE* If the door locks cycle twice, this means the registration failed. You can repeat STEP 7 until the locks only cycle one (1) time. If the locks do not cycle one (1) time by themselves, or they stop cycling altogether, then you must repeat the entire programming procedure.

8. If you have additional remotes to program, repeat STEP 7 for all remaining remotes you wish to program (You can program up to 4 remotes total).

9. Once you have programmed all your remotes, exit the programming mode by closing the driver’s door, inserting the key into the ignition, start the vehicle, turn it off, and then remove the key.

10. Test all remotes to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1 and switch the order in which you are programming the remotes.

KEY PROGRAMMING

Please make sure to read through the programming instructions completely before attempting.

You must have a black original master key to perform this procedure. If you have a grey key, or you do not have a key at all, a trip to a dealership or an automotive locksmith will be required for the programming.

1. Enter the vehicle, close and unlock all doors using the power lock switch on the driver’s door.

2. Insert your original black key into the ignition switch but do not turn the key.

3. Within fifteen (15) seconds, using the accelerator/gas pedal, press and release the pedal five (5) times.

4. Within thirty (30) seconds, using the brake pedal, press and release the pedal six (6) times.

5. Within ten (10) seconds, remove the key from the ignition switch then insert the new key to be programmed but do not turn the key. Using the accelerator/gas pedal, press and release the pedal one (1) time.

At this point the immobilizer warning lamp will begin to flash for one (1) minute (The immobilizer lamp is a small red circular light, or a small red car shape with a key light, located on your dash display or next to the steering column). After one (1) minute has passed, this light will stop blinking, indicating that the new key has been successfully programmed.

6. Additional keys must be programed within ten (10) seconds by repeating STEP 5.

7. Once you have programmed all the keys, exit the programming mode by removing the key that is currently in the ignition, then press and release the brake pedal one (1) time. You can program up to seven (7) keys at one time.

8. Test all keys to ensure they are functioning. If any did not program, restart the programming procedure from STEP 1.